An MPV can be added by right-clicking on a shaft in the Model Tree.
In the insert component dialog, select Shaft-hub connection -> Press fit -> and then select "Multiple interference fit" from the pull-down menu.
The cylindrical gear, a new shaft, or a new hub can be selected as the outer part of the MPV.
The geometry of the press fit will be displayed in the schematic diagram.
In this editor, the roughness depths can be converted from Ra to Rz according to DIN 4768. This is required for entries in Ra, as the kernel expects entries in Rz. The results will be output as preferred values in accordance with DIN 4763.
The Yrau value also provides the option of custom scalability for the conversion. The conversion factor goes into the algorithm in exponential form; Yrau= 0 corresponds to the non-scaled form in accordance with DIN 4768. Therefore, adding 1 to the scaling factor increases the calculation results to the next higher preferred number. Negative scaling factors are also possible.
The value for Ra is entered after the scaling factor. The conversion to Rz as well as its output is triggered by pressing the tab key, or by clicking in the Rz field. The box will be checked when the calculation is successfully completed.
The minimum and maximum interferences can be calculated in the calculation of fits editor, based on the specified joining diameter and the tolerances for the shaft and hub. If the previously calculated interference is less than or equal to the minimum interference, the values can be saved in the table editor with the "Apply tolerances" switch.
The materials for each part can be selected in the "MPV material data" section of the "joint information" tab in the editor.
FVA-Workbench will assign the corresponding material characteristics of each part according to the chosen material and write them in the input file. The materials characteristics themselves can be specified in the materials editor
as follows:
A special feature of the material data is that a multi-linear strain hardening characteristic curve can be specified.
The data of these characteristic curves are processed in a module of the PressFit-MPV kernel according to the Simpson rule and passed to the solver. Thus, for the first time, the strain hardening of the material under plastic stress can be included in the calculation. In practice, this depicts the real material behavior, as up to this point the calculation process was performed assuming ideal plastic material behavior, which is a significant simplification. On the other hand, this allows reserves for calculation purposes to be opened up that up to this point, depending on the material, led to very conservative design of interference fits.
The curve is modeled by entering stress points 2 through 4 and the associated strain points in the materials editor. Point 1 is set by the yield strength and modulus of elasticity of the material. In this way, the stress-strain curve becomes a part of the material, it is available every time the material is selected, and can be accessed or edited as often as necessary.
Both the tolerances and absolute deviations can be specified in this way.
Due to the many possible combinations of part diameters, materials, and interferences in the joint diameters, there is a very high likelihood of plastic intermediate states during the joining, even if the final joined state is purely elastically stressed.
In order to give the user control over this process, the program calculates the plasticity diameter for the parts after every joining process and includes them in the report. Thus, it is possible to compare the plasticity diameters of the corresponding parts after each joining process and the final joined state. For the overall result to remain plausible, the latter value may never be smaller, if the overall result is to remain plausible.
The input file for every calculation process will be included in the results view within the Model Tree, and can be accessed here. Inclusion of the echo prints (input data set) in the report is already planned for later versions of the FVA-Workbench, but is not yet available in version 4.0. The ability to save the input data (via the right-click context menu) can be used as a workaround, in which the data can be saved as a PDF file and, for example, be added to the report.
The following calculations are available for multiple interference fits:
This objective is for the calculation of multiple interference fits in which the interference in the individual joints are known or specified. Data must be entered for the following components:
Shafts
Multiple interference fitAfter successful calculation, the following output files (reports) will be created:
|
Multiple interference fit [6] |
|||||
|
Geometry data |
Fz |
Unit |
|||
|
Outer diameter after joining |
DA,nF |
76.021 |
mm |
||
|
Minimum interference |
Uk,MPV |
0.0 |
0.0 |
0.0 |
µm |
|
Maximum interference |
Ug,MPV |
0.0 |
0.0 |
0.0 |
µm |
|
Calculated interference for the joints |
Uber,MPV |
20.0 |
30.0 |
0.0 |
µm |
|
MPV plasticity diameter |
DP,MPV |
0.00 |
0.00 |
0.00 |
mm |
|
MPV related plasticity diameter |
ζMPV |
0.00 |
0.00 |
0.00 |
-- |
|
Load data |
Fz |
Multiple interference fit [6] |
Unit |
||
|
Joint 1 |
Joint 2 |
Joint 3 |
|||
|
MPV press-in force |
Fe,MPV |
0.0 |
0.0 |
0.0 |
N |
|
Calculated axial force of all joints |
FRax,ber,MPV |
35,980.1 |
38.062.0 |
0.0 |
N |
|
Calculated slip torque of all joints |
TR,ber,MPV |
1,079.4 |
1298.9 |
0.0 |
Nm |
|
MPV radial stresses (array of all joints) |
σr,MPV |
-63.63 |
-51.28 |
0.0 |
N/mm² |
|
Stresses |
Fz |
Multiple interference fit [6] |
Unit |
||
|
Part 1 |
Part 2 |
Part 3 |
|||
|
MPV inner tangential stresses |
σti,MPV |
-4.8 |
87.5 |
0.0 |
N/mm² |
|
MPV outer tangential stresses |
σta,MPV |
-12.2 |
51.2 |
0.0 |
N/mm² |
|
MPV inner equivalent stresses |
σvi,MPV |
61.4 |
121.6 |
0.0 |
N/mm² |
|
MPV outer equivalent stresses |
σva,MPV |
45.2 |
60.2 |
0.0 |
N/mm² |
|
Safeties |
Fz |
Multiple interference fit [6] |
Unit |
||
|
MPV safety against onset plastic stress |
SeP,MPV |
13.85 |
6.99 |
0.00 |
-- |
|
MPV safety against fully plastic stress |
SP,MPV |
18.79 |
14.13 |
0.00 |
-- |
|
MPV calculated slip resistance |
SR,MPV |
0.93 |
1.11 |
0.00 |
-- |
|
Multiple interference fit [6] |
|||||
|
Geometry data |
Fz |
Unit |
|||
|
Inner diameter after joining |
di,nF |
17.988 |
mm |
||
|
Plasticity diameter of the shaft |
DP,W |
0.00 |
mm |
||
|
Related plasticity diameter of the shaft |
ζW |
0.00 |
|||
|
Multiple interference fit [6] |
|||||
|
Stresses |
Fz |
Unit |
|||
|
Inner tangential stresses of the shaft |
σti,W |
-144.5 |
N/mm² |
||
|
Outer tangential stresses of the shaft |
σta,W |
-90.9 |
N/mm² |
||
|
Inner equivalent stresses of the shaft |
σvi,W |
139.8 |
N/mm² |
||
|
Outer equivalent stresses of the shaft |
σva,W |
80.8 |
N/mm² |
||
|
Multiple interference fit [6] |
|||||
|
Safeties |
Fz |
Unit |
|||
|
Safety against onset plastic stress of the shaft |
SeP,W |
6.08 |
|||
|
Safety against full plastic stress of the shaft |
SP,W |
10.52 |
|||
The graphical output includes the stress curves over the cross-section of the overall shaft-hub connections for the radial, tangential and equivalent stresses.
This objective is for the calculation of multiple interference fits in which the joint pressures are specified.
Data must be entered for the following components:
Shafts
Multiple interference fitAfter successful calculation, the following output files (reports) will be created:
|
Multiple interference fit [6] |
|||||
|
Geometry data |
Fz |
Unit |
|||
|
Outer diameter after joining |
DA,nF |
76.027 |
mm |
||
|
Minimum interference |
Uk,MPV |
0.0 |
0.0 |
0.0 |
µm |
|
Maximum interference |
Ug,MPV |
0.0 |
0.0 |
0.0 |
µm |
|
Calculated interference for the joints |
Uber,MPV |
-12.4 |
61.5 |
0.0 |
µm |
|
MPV plasticity diameter |
DP,MPV |
0.00 |
0.00 |
0.00 |
mm |
|
MPV related plasticity diameter |
ζMPV |
0.00 |
0.00 |
0.00 |
-- |
|
Load data |
Fz |
Multiple interference fit [6] |
Unit |
||
|
Joint 1 |
Joint 2 |
Joint 3 |
|||
|
MPV press-in force |
Fe,MPV |
0.0 |
0.0 |
0.0 |
N |
|
Calculated axial force of all joints |
FRax,ber,MPV |
22,626.2 |
44,527.6 |
0.0 |
N |
|
Calculated slip torque of all joints |
TR,ber,MPV |
678.8 |
1,519.5 |
0.0 |
Nm |
|
MPV radial stresses (array of all joints) |
σr,MPV |
-40.0 |
-60.0 |
0.0 |
N/mm² |
|
Stresses |
Fz |
Multiple interference fit [6] |
Unit |
||
|
Part 1 |
Part 2 |
Part 3 |
|||
|
MPV inner tangential stresses |
σti,MPV |
-135.4 |
112.1 |
0.0 |
N/mm² |
|
MPV outer tangential stresses |
σta,MPV |
-112.6 |
67.2 |
0.0 |
N/mm² |
|
MPV inner equivalent stresses |
σvi,MPV |
120.4 |
151.3 |
0.0 |
N/mm² |
|
MPV outer equivalent stresses |
σva,MPV |
99.9 |
75.8 |
0.0 |
N/mm² |
|
Safeties |
Fz |
Multiple interference fit [6] |
Unit |
||
|
MPV safety against onset plastic stress |
SeP,MPV |
7.06 |
5.62 |
0.00 |
-- |
|
MPV safety against fully plastic stress |
SP,MPV |
8.51 |
11.22 |
0.00 |
-- |
|
MPV calculated slip resistance |
SR,MPV |
0.58 |
1.30 |
0.00 |
-- |
|
Multiple interference fit [6] |
|||||
|
Geometry data |
Fz |
Unit |
|||
|
Inner diameter after joining |
di,nF |
17,993 |
mm |
||
|
Plasticity diameter of the shaft |
DP,W |
0.00 |
mm |
||
|
Related plasticity diameter of the shaft |
ζW |
0.00 |
|||
|
Multiple interference fit [6] |
|||||
|
Stresses |
Fz |
Unit |
|||
|
Inner tangential stresses of the shaft |
σti,W |
-85.2 |
N/mm² |
||
|
Outer tangential stresses of the shaft |
σta,W |
-55.3 |
N/mm² |
||
|
Inner equivalent stresses of the shaft |
σvi,W |
80.7 |
N/mm² |
||
|
Outer equivalent stresses of the shaft |
σva,W |
49.4 |
N/mm² |
||
|
Multiple interference fit [6] |
|||||
|
Safeties |
Fz |
Unit |
|||
|
Safety against onset plastic stress of the shaft |
SeP,W |
10.53 |
|||
|
Safety against full plastic stress of the shaft |
SP,W |
17.20 |
|||
The graphical output includes the stress curves over the cross-section of the overall shaft-hub connections for the radial, tangential and equivalent stresses.
This objective is for the calculation of multiple interference fits with predefined fits. Here, the minimum and maximum allowances are determined using the predefined fit, and the following data are calculated: The required joining temperatures for the inner and outer parts for each of the joining processes are also output.
The calculation and output of the joining temperatures for the individual joining processes depending on the preset or manually entered joint clearance are performed under the "fit recalculation" objective. The joining processes are provided in order by part, starting with Part 1. For shrink fits, specific upper temperature limits for heat-treated components may not be exceeded to avoid structural transformation. A mode was created in PressFit® which enables the calculation of the associated joining temperatures of the inner parts at any specified hub temperature using the following equation:
| ϑShaft | Shaft temperature |
| ϑR | Ambient temperature |
| ϑHub | Hub temperature |
| UF | Interference when joining |
| DF | Diameter of the joint |
| αA | Coefficient of linear expansion of the outer part |
| αI | Coefficient of linear expansion of the inner part |
The temperatures of the respective outer parts can be specified in the "max. heating temperature" entry field.
Similarly, specification of minimum cooling temperatures for inner parts may be necessary to avoid, for example, embrittlement of the component. This can be specified in the "min. cooling temperature" entry field. The aforementioned equation should then be changed according to ϑNabe.
If both values are specified for a joint diameter, the kernel always gives priority to the minimum cooling temperature.
When determining the joining temperatures, it should be noted that the intermediate parts are both inner and outer parts (in conjunction with the previously assembled parts) during the individual joining processes.
After successful calculation, the following output files (reports) will be created:
Data must be entered for the following components:
Shafts
Multiple interference fitAfter successful calculation, the following output files (reports) will be created:
|
Multiple interference fit [6] |
|||||
|
Geometry data |
Fz |
Unit |
|||
|
Outer diameter after joining |
DA,nF |
76.087 |
mm |
||
|
Minimum interference |
Uk,MPV |
18.0 |
14.0 |
0.0 |
µm |
|
Maximum interference |
Ug,MPV |
82.0 |
90.0 |
0.0 |
µm |
|
Calculated interference for the joints |
Uber,MPV |
82.0 |
90.0 |
0.0 |
µm |
|
MPV plasticity diameter |
DP,MPV |
0.00 |
0.00 |
0.00 |
mm |
|
MPV related plasticity diameter |
ζMPV |
0.00 |
0.00 |
0.00 |
-- |
|
Load data |
Fz |
Multiple interference fit [6] |
Unit |
||
|
Joint 1 |
Joint 2 |
Joint 3 |
|||
|
MPV press-in force |
Fe,MPV |
46,753.1 |
107,898.2 |
0.0 |
N |
|
Calculated axial force of all joints |
FRax,ber,MPV |
120,103.6 |
110,783.7 |
0.0 |
N |
|
Calculated slip torque of all joints |
TR,ber,MPV |
3,603.1 |
3780.5 |
0.0 |
Nm |
|
Gap pressure |
ƿMPV |
40.0 |
60.0 |
N/mm² |
|
|
Stresses |
Fz |
Multiple interference fit [6] |
Unit |
||
|
Part 1 |
Part 2 |
Part 3 |
|||
|
MPV inner tangential stresses |
σti,MPV |
88.6 |
364.4 |
0.0 |
N/mm² |
|
MPV outer tangential stresses |
σta,MPV |
44.0 |
230.1 |
0.0 |
N/mm² |
|
MPV inner equivalent stresses |
σvi,MPV |
267.9 |
457.7 |
0.0 |
N/mm² |
|
MPV outer equivalent stresses |
σva,MPV |
163.5 |
238.0 |
0.0 |
N/mm² |
|
Safeties |
Fz |
Multiple interference fit [6] |
Unit |
||
|
MPV safety against onset plastic stress |
SeP,MPV |
3.17 |
1.86 |
0.00 |
-- |
|
MPV safety against fully plastic stress |
SP,MPV |
5.20 |
3.57 |
0.00 |
-- |
|
MPV calculated slip resistance |
SR,MPV |
3.09 |
3.24 |
0.00 |
-- |
|
Multiple interference fit [6] |
|||||
|
Geometry data |
Fz |
Unit |
|||
|
Inner diameter after joining |
di,nF |
19.955 |
mm |
||
|
Plasticity diameter of the shaft |
DP,W |
0.00 |
mm |
||
|
Related plasticity diameter of the shaft |
ζW |
0.00 |
|||
|
Multiple interference fit [6] |
|||||
|
Stresses |
Fz |
Unit |
|||
|
Inner tangential stresses of the shaft |
σti,W |
-517.7 |
N/mm² |
||
|
Outer tangential stresses of the shaft |
σta,W |
-315.5 |
N/mm² |
||
|
Inner equivalent stresses of the shaft |
σvi,W |
512.7 |
N/mm² |
||
|
Outer equivalent stresses of the shaft |
σva,W |
278.6 |
N/mm² |
||
|
Multiple interference fit [6] |
|||||
|
Safeties |
Fz |
Unit |
|||
|
Safety against onset plastic stress of the shaft |
SeP,W |
1.66 |
|||
|
Safety against full plastic stress of the shaft |
SP,W |
3.05 |
|||
|
Calculated joining values |
Fz |
Multiple interference fit [6] |
Unit |
||
|
Joining process 1 |
Joining process 2 |
Joining process 3 |
|||
|
Required joining temperature for the outer part |
ϑAerf,MPV |
250.0 |
161.5 |
0.0 |
°C |
|
Required joining temperature for the inner part |
ϑIerf,MPV |
48.7 |
-100.0 |
0.0 |
°C |
|
Plasticity diameter of the shaft after joining process |
DPW,nF |
18.00 |
18.00 |
0.00 |
mm |
|
Plasticity diameter of Part 1 after joining process |
DP,nF1 |
40.00 |
40.00 |
0.00 |
mm |
|
Plasticity diameter of Part 2 after joining process |
DP,nF2 |
0.00 |
52.50 |
0.00 |
mm |
|
Plasticity diameter of Part 3 after joining process |
DP,nF3 |
0.00 |
0.00 |
0.00 |
mm |
|
Multiple interference fit [6] |
|||||
|
Geometry data |
Fz |
Unit |
|||
|
Outer diameter after joining |
DA,nF |
76.009 |
mm |
||
|
Fz |
Multiple interference fit [6] |
Unit |
|||
|
Joint 1 |
Joint 2 |
Joint 3 |
|||
|
Calculated interference for the joints (array of all joints) |
Uber,MPV |
18.0 |
14.0 |
0.0 |
µm |
|
Fz |
Multiple interference fit [6] |
Unit |
|||
|
Part 1 |
Part 2 |
Part 3 |
|||
|
MPV plasticity diameter (array of all hub components) |
DPA,MPV |
0.00 |
0.00 |
0.00 |
mm |
|
Relative MPV plasticity diameter (array of all hub components) |
ζMPV |
0.00 |
0.00 |
0.00 |
-- |
|
Load data |
Fz |
Multiple interference fit [6] |
Unit |
||
|
Joint 1 |
Joint 2 |
Joint 3 |
|||
|
Calculated axial force of all joints |
FRax,ber,MPV |
26,407.0 |
25,756.2 |
0.0 |
N |
|
Calculated slip torque of all joints |
TR,ber,MPV |
792.2 |
878.9 |
0.0 |
Nm |
|
MPV radial stresses (array of all joints) |
σr,MPV |
-46.7 |
-34.7 |
0.0 |
N/mm² |
|
Stresses |
Fz |
Multiple interference fit [6] |
Unit |
||
|
Part 1 |
Part 2 |
Part 3 |
|||
|
MPV inner tangential stresses (array of all hub components) |
σti,MPV |
10.5 |
40.7 |
0.0 |
N/mm² |
|
MPV outer tangential stresses (array of all hub components) |
σta,MPV |
1.9 |
21.0 |
0.0 |
N/mm² |
|
MPV inner equivalent stresses (array of all hub components) |
σvi,MPV |
52.7 |
65.3 |
0.0 |
N/mm² |
|
MPV outer equivalent stresses (array of all hub components) |
σva,MPV |
34.0 |
31.3 |
0.0 |
N/mm² |
|
Safeties |
Fz |
Multiple interference fit [6] |
Unit |
||
|
MPV safety against onset plastic stress (array of all hub components) |
SeP,MPV |
16.12 |
13.01 |
0.00 |
-- |
|
MPV safety against fully plastic stress (array of all hub components) |
SP,MPV |
25.01 |
27.16 |
0.00 |
-- |
|
MPV calculated slip resistance (array of all joints) |
SR,MPV |
0.68 |
0.75 |
0.00 |
-- |
|
Multiple interference fit [6] |
|||||
|
Geometry data |
Fz |
Unit |
|||
|
Inner diameter after joining |
di,nF |
17.991 |
mm |
||
|
Plasticity diameter of the shaft |
DP,W |
0.00 |
mm |
||
|
Related plasticity diameter of the shaft |
ζW |
0.00 |
|||
|
Multiple interference fit [6] |
|||||
|
Stresses |
Fz |
Unit |
|||
|
Inner tangential stresses of the shaft |
σti,MPV |
-102.1 |
N/mm² |
||
|
Outer tangential stresses of the shaft |
σta,MPV |
-65.4 |
N/mm² |
||
|
Inner equivalent stresses of the shaft |
σvi,MPV |
97.4 |
N/mm² |
||
|
Outer equivalent stresses of the shaft |
σva,MPV |
58.3 |
N/mm² |
||
|
Multiple interference fit [6] |
|||||
|
Safeties |
Fz |
Unit |
|||
|
Safety against onset plastic stress of the shaft |
SeP,W |
8.72 |
|||
|
Safety against full plastic stress of the shaft |
SP,W |
14.57 |
|||
The graphics output is similar to the "allowance calculation" objective. But in this case, the graphic output applies to both the minimum and maximum interference.
| MPV output attribute documentation (German) | View document |