Stiffness element file

Symbol -
Unit -
Attribute-ID external_stiffness_element
Numeric ID 4934
Value Type PMFile

The stiffness element file for entering an external stiffness matrix must be constructed as follows:

Example file: stiffness_element.txt


NUM_COUPLING_POINTS = 4

PATH_TO_STIFFNESS_MATRIX = C:\yourpath\reduced_matrix_in_harwell_boeing_format.txt

SHAFT_ID = 5 5 7 7

U_POSITION_ON_SHAFT = 440.0 637.0 53.0 446.0

COORD_DEF = 1 2 3


Explanation of attributes:

The first coupling point is the origin of the coordinate system for the reduced stiffness matrix.

The first two referenced coupling points determine the direction of the first coordinate (u-direction) of the coordinate system for the stiffness matrix.

The third coupling point indicates the third coordinate direction (w-direction) of the coordinate system for the stiffness matrix.

The default assignment for the selection of the coupling locations is 1 2 3.

 

In the event that all coupling locations are co-linear, the coordinates are defined as follows:


COORD_DEF = 1 2 0

ANGLE = 75.0


In the ANGLE line, an angle (in degrees) by which the third coordinate axis of the stiffness matrix is rotated with respect to the third coordinate axis in the global gearbox coordinate system must be specified. A positive angle is defined as rotation around the negative first coordinate direction. A zero degree angle indicates that the third coordinate direction of the stiffness matrix points in the direction of the third coordinate direction in the gearbox coordinate system.

 

For an external stiffness element for a planet carrier, an additional specification must be made for the shafts integrated in the FEM model (carrier shafts and/or planet pins). The SHAFT_REPLACED_BY_FEM line must be inserted before the coordinate definition and contains the IDs of all shafts integrated in the FEM planet carrier:


SHAFT_REPLACED_BY_FEM = 4 6


In this example, the shafts with IDs 4 and 6 are integrated into the FEM model. These could be, for example, the two carrier shafts of a dual-plate carrier assembly that are integrated in the reduced stiffness matrix. The same applies for planet pins integrated into the FEM model.

For planetary stages, the challenge is to obtain the IDs of the individual planetary shafts/pins (depending on the coupling). In the 3D model and in the calculation, the number of individual planet shafts and individual pins corresponds to the number of planets. The IDs of these individual components are relevant for the stiffness element, not the ID's of the planetary shafts/pins in the model tree. The following procedure is recommended:

The report for planet stages contains the following sketch. This makes it possible to infer the mounting position of the planetary shafts.

The mounting angles in this diagram (@0°, @120°, @240°) are specified in the attribute overview of the individual pin or individual planet shaft components (depending on the coupling) -> Geometry -> Mounting angle of the individual planet under the Occurrence in the model section:

The component name contains the ID of the corresponding shaft in brackets (in this figure: 121, 122, 123).

For the assignment of several planetary stages it is helpful to know that the IDs in newly added planetary stages are assigned in ascending order, i.e. the ID of pin in the Model Tree 120 is followed by the IDs of the individual pins 121, 122, 123. The number of individual pins corresponds to the number of planets. The IDs of the individual pins must be added in the SHAFT_REPLCAED_BY_FEM line if they are part of the FEM model. The IDs of the individual pins are also to be used in the SHAFT_ID line when connecting the planetary bearings.

If no shafts are integrated into the FEM model of the planet carrier, no entry should be made to the right of the equal sign in the SHAFT_REPLCAED_BY_FEM line.

If loads are present on the shafts that are integrated into the FEM Model of the planet carrier, such as driving torque on the carrier shaft, a corresponding coupling point must be provided in the reduced stiffness matrix. This must be taken into account in the lines NUM_COUPLING_POINTS, SHAFT_ID and U_POSITION_ON_SHAFT.

For an explanation see also the tutorial FEM-Planet Carrier.

For more information on specifying an external stiffness matrix, see:

THEMIS - Abschlussbericht AK Wb 711 I AB 1250 (in German)

For casings, the identifiers from the final report can also be used (ANZ_KOPPELPUNKTE, DATEIPFAD_STEIFIGKEIT, IW, UK, KOORD_DEF and WINKEL) whereas under IW the ID's of the shafts are to be entered in the Workbench model.